McCulloch Cabrio 433B Instruction Manual download pdf (Page 13)

S Cut only from your left to your right. Cutting on

right side of the shield will throw debris away

from the opera tor.

S Use the shoulder strap and keep a firm grip

on the unit with both hands. A properly

adjusted shoulder strap will support the

weight of the unit, freeing your arms and

hands to control and guide the cutting motion.

S Keep feet comfortably spread apart and

braced for a possible sudden, rapid thrust of

unit. Do not overreach. Keep firm footing and

balance.

S Keep blade below waist level; it will be

easier to maintain control of unit.

S Do not raise the engine above your waist as

the blade can come dangerously close to

your body.

S Do not swing unit with such force that you

are in danger of losing your balance.

Bring the engine to cutting speed before enter-

ing the material to be cut. If the blade does not

turn when you squeeze the throttle trigger , make

sure shaft is fully inserted into the engine.

Always release the throttle trigger and allow

engine to return to idle speed when not cut-

ting. The blade should not turn while the en-

gine is running at idle. If the blade turns at idle,

do not use your unit. Refer to the CARBURE-

TOR ADJUSTMENT section or contact your

authorized service dealer.

S Maintain good firm footing while using the

unit. Do this by planting feet firmly in a

comfortable apart position.

S Cut while swinging the upper part of your

body from left to right.

S Asyoumoveforwardtothenextareatocut,

be sure to maintain your balance and footing.

Cut using the 2

o’clock to 4 o’clock

position of the

blade

2 o’clock

4 o’clock

RECOMMENDED CUTTING POSITION

WARNING: The operator or others

must not try to clear away cut material with the

engine running or the blade turning to avoid

serious injury. Stop engine and blade before

removing materials wrapped around blade or

shaft.

ADDITIONAL SAFETY RULES

FOR OPTIONAL ATTACHMENTS

WARNING: For each optional attach-

ment used, read entire instruction manual be-

fore use and follow all warnings and in-

structions in manual and on attachment.

WARNING: Ensure handlebar is

installed when using edger or brushcutter at-

tachments. Attach handlebar above arrow on

safety label on the upper shaft (engine end of

unit). If your edger or brushcutter attachment

does not include a handlebar , a handlebar ac-

cessory kit (#530071451) is available from

your authorized service dealer.

Handlebar

EDGER SAFET Y

WARNING: Inspect the area to be

edged before each use. Remove objects

(rocks, broken glass, nails, wire, etc.) which

can be thrown by the blade or can wrap

around the shaft.

WARNING: Blade rotates momen-

tarily after the trigger is released. The blade

can seriously cut you or others. Allow blade to

stop before removing it from the cut.

S Throw away blades that are bent, warped,

cracked, broken or damaged in any other

way. Replace parts that are cracked, chipped,

or damaged before using the unit.

S Do not attempt to remove cut material nor

hold material to be cut when the engine is

running or when cutting blade is moving.

S Always keep the wheel and depth adjusting

skid in contact with the ground.

S Always push the unit slowly over the ground.

Stay alert for uneven sidewalks, holes in the

terrain, large roots, etc.

S Always use the handlebar when using edger

attachmen t.

BLOWER/VACUUM SAFET Y

WARNING: Inspect area before start-

ing unit. Remove all debris and hard objects

such as rocks, glass, wire, etc. that can rico-

chet, be thrown, or otherwise cause injury or

damage during operation.

S Do not set unit on any surface except a clean,

hard area while engine is running. Debris

such as gravel, sand, dust, grass, etc., could

be picked up by the air intake and thrown out

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Comments to this Manuals

No comments

McCulloch Cabrio 433B Instruction Manual Page 13

Comments to this Manuals

Related products and manuals for Power tools McCulloch Cabrio 433B